Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
We have found this article on Tools You Need to Install a New Bathtub directly below on the net and felt it made good sense to talk about it with you over here.
Mounting a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub as well as position the new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub as well as set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly help you install a brand-new tub in your shower room if you have currently acquired a new tub and also do not need to change the plan of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be fairly problematic as a result of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the tap in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the supply of water and examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the tub and also inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait until the bathtub has been used at least once as this will settle it into its final position.
Preparing for the Setup
First of all, the supporting framework supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bath and also the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece on Tools You Need to Install a New Bathtub while exploring the search engines. Sharing is good. Helping others is fun. We recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Visit Link Report this page